Parts & Service
Do you sell any kayak covers for winter storage?
We do not unfortunately sell any kayak covers for winter storage. The cold and some snow is not a problem but the sunlight UV rays are the main issue. Also heavy snow load more than a few feet can compress the hull so will want to clear off any large ...
Gel coat repairs for composite kayaks
We don't have our own video for gel coat repairs but I would suggest this one from Nova Craft canoes. follow these instructions: https://www.novacraft.com/blog/gelcoat-repair/ There are kits available on Amazon. ...
I am looking for the V-Block part that holds the rudder in place when not in use. This is for an Esperanto.
The V-Block for the Esperanto can be purchased here https://boutiqueborealdesign.com/products/umat-008-v-bloc-for-esperanto?variant=43089404100866 Assuming you have the bolts that hold on old one, you can re-use them. If not please just message me ...
I need to order a new seat back cover for my BorealDesign kayak.
Hello, if your BorealDesign kayak is a more recent model since 2018-19 onwards then the Flex 4 seat cover will fit. You can view and purchase that here: ...
I need rubber hatch cover replacements for my BorealDesign kayak.
Over time the rubber does dry out and it gets harder for them to be put on or off. The day hatch replacement is here: https://boutiqueborealdesign.com/collections/hatch-covers/products/umat-166-bd-day-hatch-coversmall?variant=28063930417236 The front ...
How to remove and replace the paddle lock on your adjustable BorealDesign paddle.
In this quick 25 sec video we will show you how to remove and replace the paddle lock on your adjustable Boreal, Riot or Beluga paddle. You will need 1 x 3 mm Allen Key. View the Video Here.
How do I fix a leak in my compartment or hatch?
The first step to fixing a leak in your compartment/hatch is identifying where the water is entering. The possibilities are: The hatch cover is not forming an adequate seal, perhaps due to improper maintenance (requires regular cleanings to remove ...
How do I install safety rescue straps on back deck of my kayak?
Installing safety rescue straps on your Riot or Boreal Design kayak is relatively straight forward if not already there. 1) Locate the pin holes on top deck to drill. Alternatively use the holes in each end of strap as a guide to mark the holes ...
5 Steps To Patch Your Kayak With Gator Guards
This is a great article from Kayak Angler on how to apply a patch to a poly rotomolded boat or ABS Thermoformed boat using products like Gator Patch. Even tough rotomolded and thermoformed kayaks need protection and repair. Gator Patch polyester ...
Do you sell rudders, skeg kits and replacement parts?
Yes we sell rudder and skeg kits for certain models and replacement parts for through our online store. You can have them shipped anywhere in North America and Internationally. Hope that helps, see you on the water!
I have a problem with my skeg. How do I fix and adjust my skeg line on my BorealDesign kayak?
We walk you through the steps in this video on how to adjust and fix the skeg line and tension on your Riot or Boreal Design kayak.
What is the best UV-protection spray or wax for my kayak for long term maintenance?
Regular applications of UV-Protection products is recommended to keep your boat's colour and material from being degraded by the sun, rain and weather. We recommend a few different products: 303 Protectant spray - sold at many hardware and marine ...
How to install a kayak rudder support
in this article and attached powerpoint slide set with videos we show you how to install the rudder support mount for your Boreal Design or Riot Kayak. See interactive powerpoint file attached that has videos embedded. Parts include 2 short ...
How do I install my rudder on a Boreal Design Kasko or Ookpik?
If your rudder is not already installed on your Boreal Design Kasko or Ookpik kayak, here are the steps to to do this: Take out the long bolt and nut from the rudder wing assembly Assemble the rudder kit to fit the rudder support by installing the ...
How to repair and replace the rudder pedal support flanges on a thermoformed ABS kayak
This article and attached file with video (see download link at the bottom of the page) walks you through the steps to replace and install new flanges to attach your kayak pedals to in a thermoformed ABS kayak for Boreal Design or Riot Kayaks. Tools ...
How to fix bulkheads on thermoformed ABS kayaks
If you are experiencing the issue of the bulkhead becoming separated or unglued on your Thermoformed ABS kayak, there is a relatively easy fix following these steps and with white Sikaflex marine caulking. See, download and print these instructions ...
How to restore finish and colour to an ABS thermoformed plastic kayak
It is relatively simple to restore the finish to an ABS thermoformed kayak with the right acrylic lacquer spraypaint and a few simple tools/ materials needed. Download the following article (see bottom of page) for step by step instructions on how to ...
How do I install a Flex 4 Seat in an ABS thermoformed plastic Boreal Design kayak?
In this video we show you how to install a new Flex 4 Seat in your ABS Thermoformed BorealDesign kayak. Maybe you are upgrading or replacing your existing seat, you will be sure to enjoy the comfort and ease of adjustment of a new Flex 4 seat. Parts ...
How do I install a Flex 4 Seat in a rotomolded plastic BorealDesign kayak?
In this video we show you how to install a new Flex 4 Seat in your BorealDesign kayak. Maybe you are upgrading or replacing your existing seat, you will be sure to enjoy the comfort and ease of adjustment of a new Flex 4 seat. Parts included: Seat ...
The skeg does not deploy or lower all the way on my Boreal Baffin, Labrador or Pakesso kayak. How do I fix this issue?
Making an adjustment to your skeg line so it lowers all the way is relatively easy to do. 1) Use tape to secure the skeg so does not fall down; 2) Go to the Skeg-Dial Control, carefully pick off the small black cap cover (it is glued with silicone), ...
Is it possible to open up a Beluga bilge pump and clean it out? I have some small rocks inside.
It is not recommended to open up the hand pump but see if the rocks or debris can be flushed out with water, high pressure hose or a pressure washer maybe Hope this helps,
Why does may kayak always keep turning to one side?
In a bit of wind, kayaks will always turn to one side. The kayak often turns to the direction of the wind which is natural. Sailboats will do this also. This is known as weathercocking. You need to use your paddle to steer or rudder to counteract ...
How to replace the hull support / water bottle holder on a BorealDesign thermoformed ABS kayak
Here are the necessary things to replace a broken support / bottle holder on a thermoformed ABS kayak. Materials and Tools: a sharp utility knife small prybar sand paper gloves glue - we suggest a high quality plastic/metal adhesive which can be ...
I have a problem with my skeg, how do I fix my skeg? My skeg control lever only goes down to half way or is stuck
We recommend the following as different options to fix: Rest or lift the stern (rear of kayak) above the ground or water, so the skeg can lower and raise freely. Try to pull firmly on the skeg to get it down all the way, till skeg reaches its full ...
How do I fix or re-seal a foam kayak bulkhead?
Due to the flexing of the kayak both in transport and on the water, over time the foam wall separating the cockpit from the dry compartments (better known as a bulkhead) may come loose. The following video will show you how to inspect, prepare, fix ...
How do I fix a leaking hatch (and replace the rim with a new seal)?
Replacing your hard plastic hatch rim on your kayak is relatively easy. 1. If the leak in your rim is small then try the following first with some silicon: Tear off the removable glue/silicon of the hatch rim where it is leaking as best you can by ...
How to repair or fix a cracked kayak
There is no reason why you cannot fix a plastic ABS Thermoformed or Composite boat on your own. Using these resources and the right tools it can be done. If it seems too difficult, then many kayak dealers and also marinas offer this service. Ask ...
How do I order parts?
We sell many replacement parts for our different brands of kayaks and boards. Please visit our online store here. Under Parts and Service menu you will find: Seats Seat Back & Covers Skeg / Rudder Hatch Covers Deck Outfitting Components Find Parts ...
How to adjust the rudder support when it is crooked
In this brief article we show you how to re-align a mis-aligned or slightly crooked rudder bracket / rudder mount. You can also download this as a document (see link at bottom of page) to print out and refer to as well below.
I have a small cut in the hull of my kayak. Is it possible to repair this damage?
Yes, even though it is very hard to cut or damage our kayaks, if it does happen, then please order your repair material from one of our dealers where you bought your kayak. Please note that not all colors maybe available. You will then need a ...
I am having trouble fitting my rubber hatch on my kayak. What do I do?
Sometimes the rubber hatches are a bit difficult to put on the hatch rim. The fit is tight so that if forms a good seal to prevent water from entering the kayak. The best way is to: Start on one side pushing hatch down and running your hand along the ...
Basic kayak maintenance
We’ve put a lot of time and thought into providing you with a quality craft and we stand behind our product 100%. By reading your kayak’s warranty agreement and following these few simple maintenance steps, you should have years of problem-free fun ...